Most of our service manuals are immediately available as a PDF Download that will provide the service information you need right away. Most of our service manuals will include disassembly instructions, schematic diagrams, parts lists, exploded views, troubleshooting, wiring diagrams and much, much more.
Service Manual, Paper Manual. Windows 7 Driver Installation Instructions. Mac OS X PCL6 Driver. PostScript Driver. Microsoft Certified. PostScript Driver Microsoft Certified. Solaris Driver. Mac OSX USB Driver for Macintosh 9.
Twain Scanner Driver. ControlCentre Driver. I agree to the Terms and Conditions Visit. Font Management Utility. The mes- normal operating temperature, the fuser unit may consequently be damaged. Press Start to re-dial immediately, or press This is the set if messages displayed when the machine encounters scan to e-mail problems.
Stop to cancel the re-dial procedure. Try deleting unused num- Use this RAP when the machine has a fax fault but does not display a message. If a fax fault bers. The machine has detected a problem connected with IP addresses. To isolate and identify the source of unusual noises.
Use this RAP when the scanner produces black copies, but on-line printing is normal. Use this RAP when there are black lines or bands along the process direction, as shown in Fig- ure 1. Use this RAP when the machine produces light images in all modes, as shown in Figure 1.
Figure 1 Vertical white lines Figure 1 Light image Procedure Use this RAP when the machine produces dark images in all modes. Ensure the transfer roller contacts, which are housed within the PMO - housing terminal MC2 are not deformed. Use this RAP when the printed sheets have blank areas, not forming a regular pattern. Specification Make a copy of the test pattern. Compare the copy with the solid area density scale.
The den- sity of the 1. Refer to Table 1. REP 1. REP 2. REP 4. Page Rep 1. Page Rep 2. Remove the rubber contacts. Remove 13 screws. Figure 3 Rubber contacts removal Remove the key pads, Figure 4. Remove the key pads. Figure 4 Key pads removal Repairs and Adjustments March Page 79 If installed, remove the cover E-mail, Figure 5. Remove the key plate, Figure 7. Remove the cover E-mail by gently squeezing together the locking tabs located on the underside of the assembly. Remove key plate. Figure 7 Key plate removal Remove the E-mail key pad, Figure 8.
Page Rep 4. Disconnect the power cord from the customer Release the harness. To make the replacement of the Parts List on PL 4. Page 84 Remove 5 screws.
Remove 1 screw, then the cover bracket motor. Remove the PMO - dummy base frame, then the cam. Remove the PMO lock developer. Page Rep 5. REP 5. In the lowered position the coun- Open the MEA unit - cover terbalance springs are compressed and can cause injury when released. Remove 4 screws. Remove the MEA unit - cover open from the rear pivot, then the front pivot.
Remove the MEA unit support pick up assembly. Page 89 If necessary, remove 4 Remove 1 E-clip, then the screws. Remove 1 E-clip, then the MEC clutch small feed.
Disconnect the inline con- nector. Remove the guide - M scan assembly. Remove 1 E-clip, 1bearing, then the MEA unit - pickup. Figure 13 Guide - M scan assembly removal Page 90 Remove 3 screws, then the guide - M duplex inner. Remove the MEA unit guide pickup assembly.
Remove 3 screws, then the Remove 3 screws. Disconnect CN5. Disconnect the MEC - clutch small duplex inline connector. Page Rep 6. REP 6. Parts List on PL 6. Page 93 Disconnect CN3. Remove 3 screws, then the unit - LSU. Replacement is the reverse of the removal procedure.
Page Rep 7. Page Rep 8. Page Carefully push a 2mm allen key or similar tool into the hole to release the bearing. While the bearing is released, rotate it 90 degrees to align the clips with the cutouts in the machine frame. Slide the bearing forward to remove. Page Rep
0コメント