So I suspect a power supply issue on AP2. I took the injector and power supply that fed AP2 out of the patch closet. When connecting AP2 directly to the power supply, it came to life immediately. So I figure the injector is defective. On the same day, I notice AP4 is also dead again all LEDs off, no idea how long, could have been that day or could have been a few days - it has definitely been working after the power cut that appeared to have killed AP2.
Later that day, I took the injector and power supply that fed AP4 out of the patch closet. Should have triggered questions, but did not immediately.
Last Thursday I got the new injectors and power supplies. AP2 does not start. AP2 starts immediately. As far as I can tell, it stopped working after I briefly disconnected and reconnected the patch cable between injector3 and the patch panel in the patch closet.
The LEDs on switch port 1 are off. I have since tried to power cycle both switches took power off both, waited a while, poewerd both back on. No change. PS: the APs ran firmware THis is when I found out AP2 was dead. AP2 was still on It was upgraded to I am trying now to deploy the setup that works on some APs and doesn't work on others. Could one of the experts confirm or deny?
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection.
I've tried every work-about I could find and always get the error code, and am at a loss as to what else I can try to get the devices to connect to the access point. Apr 16, I need to know if p with outdoor antennas supports Point-to-Point Wireless Bridging? Jun 20, Version Jul 9, I had to reset my access point but the login screen fails to appear to lock the router. Please check your email for further instructions.
Enter a new password. Cisco Systems. Cisco Systems User Manual Download for 1. Document part number: 1 About this Guide This Guide provides instructions on how to install and configure your Cisco Aironet series Access Point. Warning Warning Warning. Statement Installation of the equipment must comply with local and national electrical codes.
Ensure that the protective device is rated not greater than: 20A. Statement Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use.
Statement The fasteners you use to mount an access point on a ceiling must be capable of maintaining a minimum pullout force of 20 lbs 9 kg and must use all 4 indented holes on the mounting bracket. Use only with listed ITE equipment.
Note Note Note Note. You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add.
Get 1 for every time someone downloads your manual. Buy as many as you need. View and download manuals available only for. Register and get 5 for free. Upload manuals that we do not have and get 1 for each file. Get 1 for every download of your manual. Buy as much as you need.
Turn on suggestions. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Showing results for. Search instead for. Did you mean:. All Community This category This board. How to find the installation manual for access point. Labels: Aironet Access Points. Latest Contents. When operating in Chile, you must ensure that your access point Transmitter Power setting never exceeds 20 mW.
When shipped from the factory, the RM21A radio modules with the 5-dBi integrated antenna support the channels and maximum power levels listed in Table for their regulatory domain. When shipped from the factory, the RM21A radio modules with the 9-dBi integrated antenna support the channels and maximum power levels listed in Table for their regulatory domain. When shipped from the factory, the RM22A radio modules support the channels and maximum power levels listed in Table for their regulatory domain.
Table lists special restrictions for wireless operation in some countries. End user must limit 2. End user must limit 5 GHz operation to to and to MHz. This section provides instructions for changing the series access point output power to comply with the maximum power limits imposed by special regulatory and country restrictions see Table , Table , Table , the "Maximum Power Levels in Some Regulatory Domains with External Antennas" section , and the "Special Country Restrictions" section.
Note Administrator privileges may be required in order to change access point settings. Note Regulatory domains are set at the factory and cannot be changed by the user. To change the access point output power level, follow these instructions:. Step 1 Use your web-browser to access your access point. Step 2 When the Summary Status page appears, click Radio Step 3 Click Settings and the radio settings page appears.
Step 4 For the
0コメント